MSBTE Electrical Engineering 3rd Semester Micro Project Topics & Ideas MSBTE Diploma I Scheme Projects

MSBTE Electrical Engineering 3rd Semester Micro Project Topics & Ideas MSBTE Diploma I Scheme Projects 

22324 Electrical Circuits ECI

a.   Single  Phase  A.C.  series & parallel  Circuits:  Prepare series  and  parallel  LED 1amp/load(R,L,C)  circuit.  Measure  the  response  and  draw  vector  diagram.  Calculate power factor for the circuit.

b.   Three  phase  balanced   circuits:  Prepare  three  phase  network  of  balanced  load  at 230volts and determine  phase and line quantities and also calculate active and reactive power for the given load.

i.    Star connection

ii.   De1ta  Connection

c.   Three  phase  unbalanced  circuits:  Prepare  three  phase  network  of  unbalanced  load and  determine  phase  and  line  quantities  and  also  calculate active  and  reactive  power for the given load.

i.    Star connection

ii.   Delta connection

d.   Principles   of‘   circuit   analysis   and    Network   theorem:   Prepare   power   point presentation   on  source   transformation,  star  delta  transformation,  mesh   and   nodal analysis, Network  theorems for the given network.

e.   Solve the given  Electric circuit problems using PSpice/Matlab software.

22325 Electrical and Electronic Measurements EEM

a)   PMMC   and   MI   instrument:   Dismantle   any   PMMC   and   MI  instrument   each available   in   the   laboratory/workshop   and   Identify   different   parts  i.e coil, spring, magnets, former etc. and  again  assemble the same.  

b)    Wattmeter :   Dismantle   either cut   types   of  wattmeter   available   in   the   

laboratory identify  the pressure coil and cm rent coil anal again assemble the same.

c)   Digital  energy  meter:  Collect  data  of power  consumption  of the equipment  

installed in  departmental  laboratories  and  workshops  of  the  polytechnic  using  Digital  energy meter.

d)   CRO and  DMM:  using  CRO  and  DMM  test  all  electronic  and  electrical  circuits  in laboratory.

e)   Tri-vector meter: Use Tri-vector meter for its practical utilization in LT consumers.

22326 Fundamentals of Power Electronics FPE

a.     Power  Electronic Devices: Build  and test the circuit of electronic switch  using power transistor  and  control  the operation  with  wireless devices.

b.     Thyristor family  devices: Build and test the circuit  of digital logic gates : AND , OR , NOT . NAND . NOR , Ex-OR , Ex-NOIR   using SCRs ( any  loin’).

c.     Turn-on  and Turn-off  methods:  Build and test the circuit of

i) PUT and

ii) UJT relaxation oscillator.

d.  Phase  controlled  rectifier:  Construct and  test  a  circuit  of  fractional  HP   DC  motor speed control  (Open Loop).

c. Industrial control circuits:  Build  and test circuit of

i)  fan regulator  using TRlAC — DJAC or

ii) SCR lamp flasher.

22327 Electric Power Generation EPG

a.     Prepare a labeled  clay model  and other materials of coal fit ed thermal  power plant. 

b.      Prepare a labeled  clay model  and other materials of gas tired  thermal  power plant. 

c.     Prepare a labeled clay model  and other materials of diesel  fired thermal  power plant.

d.     Prepare  a  labeled  clay  model  and  other  materials  of  nuclear  powered  thermal  power plant.

e.     Prepare a labeled  clay  model  and other materials of large hydro power plant. 

f.     Prepare a labeled clay model anal other materials of micro hydro power plant.

g.     Prepare a labeled  clay model  and other materials of CSP

h.     Design  a small  wind turbine or some of its component.

22328 Electrical  Materials and Wiring Practice EMW

a.     Draw labeled  lighting circuit diagram, list the accessories  used with their specifications and complete wiring    work  of following  simple electrical circuits on test board with appropriate testing under guidance of supervisor / teacher

b.     Circuit consists of suitable MCE, one lamp holder indicate, one 5 A five pin socket and two 5 A single  pole switches. 

c.    Circuit consisting of suitable MCB, one call bell, one indicator, one lamp control from two places, three switches [Two switches are two way controlled] (all for 5A rating)

d.     Circuit consisting o1 relevant MCB, 1 5A single pole switch, one indicator, one 5 pin 15A  Power  soc1‹et.

e.     Prepare series test board containing one lamp, one indicator, one socket for 230 V 

operations.

f.     Latest techniques  in cabling and wiring

MSBTE Diploma All Branch Project Ideas

MSSBTE has suggested small projects in MSBTE I scheme. A student plans to undertake only one micro-project which should be assigned to him at the beginning of the semester. The first four semesters are group-based micro-projects. However, in the fifth and sixth semesters, the problem-solving skills and confidence of each student should be taken as individually as possible so that he can contribute to the projects of the industry. In some situations where groups have to be formed for small-scale projects, the number of students in the group should not exceed three.

Area of Projects Micro-projects can be industry-based, Internet-based, workshop-based, laboratory-based, or field-based. Each micro-project should include two or more COs which are actually a combination of Pro, UO and ADO. Each student must keep a dated work diary of personal contributions to the project work and present his / her seminar before submitting it.

MSBTE Diploma All Branch Projects:

1. Computer Engineering 
2. Information Technology 
3. Civil Engineering 
4. Electrical Engineering
5. Mechanical Engineering  
6. Electronic Engineering

1.  You can suggest us projects please let us know in our comment section.
2. Format is  1.Name: ******* 2.Branch: ******* 3.Semester: ****** 4.Project Topic: *****